Mathias Agmell

Fler filtreringsmöjligheter
  1. 2018
  2. FE simulation and experimental verification of side-flow and burr formation in machining of oxygen-free copper

    Mike Olsson, Henrik Persson, Mathias Agmell, Volodymyr Bushlya & Jan Eric Ståhl, 2018 jan 1, Procedia CIRP. Vol. 72. s. 1427-1432 6 s. (Procedia CIRP).

    Forskningsoutput: Kapitel i bok/rapport/Conference proceedingKonferenspaper i proceeding

  3. 2017
  4. Correlation between edge radius of the cBN cutting tool and surface quality in hard turning

    Zhao, T., M. Agmell, Johan Persson, V. Bushlya, J. E. Ståhl & J. M. Zhou, 2017 jul 1, I : Journal of Superhard Materials. 39, 4, s. 251-258 8 s.

    Forskningsoutput: TidskriftsbidragArtikel i vetenskaplig tidskrift

  5. MODELLING SUB-SURFACE DEFORMATION INDUCED BY MACHINING OF INCONEL 718

    Mathias Agmell, Aylin Ahadi, Jinming Zhou, Volodymyr Bushlya, Peng, R. L. & Jan-Eric Ståhl, 2017 jan 31, I : Machining Science and Technology An International Journal. 21, 1, s. 103-120 17 s.

    Forskningsoutput: TidskriftsbidragArtikel i vetenskaplig tidskrift

  6. Modeling subsurface deformation induced by machining of Inconel 718

    M. Agmell, A. Ahadi, J. M. Zhou, Peng, R. L., V. Bushlya & J. E. Ståhl, 2017 jan 2, I : Machining Science and Technology. 21, 1, s. 103-120 18 s.

    Forskningsoutput: TidskriftsbidragArtikel i vetenskaplig tidskrift

  7. The Influence the Uncut Chip Thickness has on the Stagnation Point in Orthogonal Cutting

    Mathias Agmell, Johansson, D., Laakso, S. V. A., Aylin Ahadi & Jan Eric Ståhl, 2017, I : Procedia CIRP. 58, s. 13-18 6 s.

    Forskningsoutput: TidskriftsbidragArtikel i vetenskaplig tidskrift

  8. Too Sharp for its Own Good – Tool Edge Deformation Mechanisms in the Initial Stages of Metal Cutting

    Laakso, S. V. A., Zhao, T., M. Agmell, A. Hrechuk & J.-E. Ståhl, 2017, I : Procedia Manufacturing. 11, s. 449-456

    Forskningsoutput: TidskriftsbidragArtikel i vetenskaplig tidskrift

  9. 2015
  10. Numerical Modelling and Analysis of Orthogonal Metal Cutting

    Mathias Agmell, 2015, Lund University (Media-Tryck). 206 s.

    Forskningsoutput: AvhandlingDoktorsavhandling (sammanläggning)

  11. 2014
  12. Identification of plasticity constants from orthogonal cutting and inverse analysis

    Mathias Agmell, Aylin Ahadi & Jan-Eric Ståhl, 2014, I : Mechanics of Materials. 77, s. 43-51

    Forskningsoutput: TidskriftsbidragArtikel i vetenskaplig tidskrift

  13. 2013
  14. The link between plasticity parameters and process parameters in orthogonal cutting

    Mathias Agmell, Aylin Ahadi & Jan Eric Ståhl, 2013 jan 1, 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO). Elsevier, Vol. 8. s. 224-229 6 s. (Procedia CIRP).

    Forskningsoutput: Kapitel i bok/rapport/Conference proceedingKonferenspaper i proceeding

  15. 2012
  16. Modelling Subsurface Deformation in High Speed Machining of Inconel 718

    Mathias Agmell, Jinming Zhou, Aylin Ahadi, Volodymyr Bushlya, Peng, R. L. & Jan-Eric Ståhl, 2012. 9 s.

    Forskningsoutput: KonferensbidragKonferenspaper, ej i proceeding/ej förlagsutgivet

  17. The affect of Johnson Cook plasticity parameters on the cutting process parameters

    Mathias Agmell, Aylin Ahadi & Jan-Eric Ståhl, 2012, (Submitted) Proceedings of the 5th Swedish Production symposium (SPS'12). Swedish Production Academy

    Forskningsoutput: Kapitel i bok/rapport/Conference proceedingKonferenspaper i proceeding

  18. 2011
  19. A numerical and experimental investigation of the deformation zones and the corresponding cutting forces in orthogonal cutting

    Mathias Agmell, Aylin Ahadi & Jan-Eric Ståhl, 2011, Advanced Materials Research. Trans Tech Publications Ltd, Vol. 223. s. 152-161 8 s.

    Forskningsoutput: Kapitel i bok/rapport/Conference proceedingKonferenspaper i proceeding

  20. Experimental Study of the Minimum Chip Thickness during the Machining of Duplex Stainless Steel

    Fredrik Schultheiss, Mathias Agmell, Högrelius, B., Volodymyr Bushlya & Jan-Eric Ståhl, 2011, AMST'11 - Advanced Manufacturing Systems and Technology. Kuljanic, E. (red.). Faculty of Engineering, Rijeka, Croatia, s. 175-189

    Forskningsoutput: Kapitel i bok/rapport/Conference proceedingKonferenspaper i proceeding

  21. 2010
  22. FE analyses of orthogonal cutting

    Mathias Agmell, Aylin Ahadi & Jan-Eric Ståhl, 2010, s. 120-125. 6 s.

    Forskningsoutput: KonferensbidragKonferenspaper, ej i proceeding/ej förlagsutgivet