On Optimal Control for Concept Evaluation and System Development in Construction Machines

Forskningsoutput: AvhandlingDoktorsavhandling (monografi)

181 Nedladdningar (Pure)

Sammanfattning

The main goal with this thesis is to develop a method to maximize the fuel efficiency [ton/l] in construction machines, while fulfilling the desired productivity [ton/h]. This is achieved by focusing on two of the main influencers; the machine concept evaluation and the development of operator assist systems. To be able to perform a concept evaluation that is unbiased from control engineering experience and test repetitiveness, an optimal control algorithm based on dynamic programming, which ensures global optimum, is developed. This algorithm is also able to handle the system optimization that is a necessity when performing a machine concept evaluation. The optimal control results from the concept evaluation are able to provide input when developing control strategies for operator assist systems, automatic functions and autonomous machine control.
The method is demonstrated on a wheel loader, working in a production chain, but can be applied to other construction machines, for example articulated haulers and excavators. Common denominators can be found with forestry equipment, agriculture machines and on road vehicles. The optimal control algorithm is put to test by challenging the calculated theoretical optimum with measured data from an extensive empirical study to test the validity of the global optimum found.
The optimal control algorithm, based on dynamic programming, successfully works. The result demonstrates approximately 14% better fuel efficiency in a gravel application, compared to the most fuel efficient operator’s best work cycle in the empirical study. The best measured work cycle is approximately 30% better than the average in the study. A similar result is shown in a timber grapple application.
The proposed method, and the algorithm developed, works for all three investigated machine concepts, enabling an unbiased concept evaluation and system optimization. The method is demonstrated on a concept comparison between a conventional wheel loader, a parallel hybrid wheel loader and a series hybrid wheel loader. The results from the concept comparison example indicate that the parallel hybrid has about 5% higher fuel efficiency and the series hybrid wheel loader has around 23% higher fuel efficiency compared to the conventional machine, which is used as baseline, at the same productivity. In an example of a system optimization for the primary energy converter, the genset, internal combustion engine and electrical machine, in the series hybrid wheel loader indicate that the optimal power rating of the genset in the investigated application is 0.6 times the internal combustion engine power rating of the conventional wheel loader. Even if the factor 0.5 showed even higher fuel efficiency, that power rating is not allowed due to complete machine performance requirements. The difference between the largest genset power rating, which is equivalent to the power rating of the conventional wheel loader, and the optimal, is approximately 6% higher fuel efficiency at the same productivity.
With the proposed method it is shown how to extract input to the development of operator assist systems, automatic functions, and autonomous construction machine control development from the optimal control results. The results are attained from the optimal control calculations performed in early development in the concept evaluation and system optimization. This also implies that the optimal control results, if used in the development of these advanced functions can increase the average fuel efficiency by up to 35 45%. The percentage is dependent on the operator´s proficiency and application according to the conclusions from the empirical study. A suggestion of how to use the optimal control results as input, when developing operator assist systems, automatic functions and autonomous machine control, is also presented.
Originalspråkengelska
KvalifikationDoktor
Tilldelande institution
  • Industriell elektroteknik och automation
Handledare
  • Alaküla, Mats, handledare
Sponsorer för avhandling
Tilldelningsdatum2018 sep. 7
UtgivningsortLund
Förlag
ISBN (tryckt)978-91-88934-91-8
ISBN (elektroniskt)978-91-88934-90-1
StatusPublished - 2018

Bibliografisk information

Defence details
Date: 2018-09-07
Time: 11:15
Place: lecture hall M:B, building M, Ole Römers väg 1, Lund University, Faculty of Engineering LTH, Lund
External reviewer(s)
Name: Rizzoni, Giorgio
Title: Professor
Affiliation: Ohio State University, USA
---

Ämnesklassifikation (UKÄ)

  • Teknik och teknologier

Fingeravtryck

Utforska forskningsämnen för ”On Optimal Control for Concept Evaluation and System Development in Construction Machines”. Tillsammans bildar de ett unikt fingeravtryck.

Citera det här